Aircraft can land in fog when the complete operation is approved for the available visibility. That approval is a chain: the runway and instrument system, aircraft equipment, crew qualification, airline procedures and reported conditions must all meet the applicable minimum. Autoland is one part of that chain, not a button that makes visibility irrelevant.
Visibility and ceiling are different constraints
A METAR reports prevailing visibility and cloud layers. Runway visual range, or RVR, is a runway-specific estimate of how far a pilot can see high-intensity lights or markings along the runway. RVR can differ among touchdown, midpoint and rollout sensors. A general airport visibility number therefore does not fully describe the landing runway.
Decode those groups in the METAR guide. Fog is FG, while mist is BR in the coded report. The operational decision uses the current report, approach chart, notices, runway condition and operator authorization, not the name of the phenomenon alone.
The approach needs precise guidance
An Instrument Landing System provides lateral guidance through the localizer and vertical guidance through the glideslope. Approach lighting helps the crew transition from instruments to visual references. Ground Based Augmentation System approaches can support precision guidance at equipped airports. The runway, transmitters, lighting, backup power and protected signal areas must satisfy the category of operation.
Traffic on the ground can interfere with sensitive guidance areas, so controllers protect larger ILS critical areas during low-visibility operations. That increases spacing and restricts taxi movement. The airport can remain open while its hourly capacity falls substantially.
CAT I, CAT II and CAT III are operating categories
Categories describe progressively lower decision heights and visibility minima, with exact values depending on rules and authorization. CAT II and CAT III operations demand more capable systems and tighter controls than a standard CAT I approach. The FAA's current low-visibility systems guidance covers takeoff, precision approach, landing and rollout criteria.
CAT III does not mean every aircraft can land with no external reference in every circumstance. The aircraft must have the required redundancy and status, the crew and operator must be authorized, and the destination infrastructure must be available. A maintenance message can reduce an aircraft's capability for that flight. A lighting or ILS outage can raise the airport minimum.
What autoland does and does not do
In an approved configuration, automatic flight-control systems can follow the approach, flare, touch down and, in some installations, track the runway during rollout. The crew configures and monitors the system, verifies its mode changes and remains responsible for a go-around if required conditions are not met.
Crews sometimes conduct autolands in good weather to maintain equipment or qualification, so an automatic landing is not proof that visibility was poor. Conversely, some low-visibility approaches end in a manual landing after the required visual references appear. Public ADS-B data cannot reliably identify which occurred.
Why fog still causes delays and diversions
Low visibility reduces runway acceptance rates, increases spacing, slows taxi and limits which aircraft or crews can complete the approach. If conditions fall below the authorized minimum, an aircraft must hold, divert or use another suitable runway. Fuel, alternate weather and traffic determine how long a crew can wait.
A tracker may show holding loops or a diversion, but the shape alone cannot prove fog was the cause. Compare the track with the observation time, forecast change windows and airport notices. The observed aviation alerts page also distinguishes a broadcast squawk from an assumed outcome.
A practical passenger check
Look for three signals: persistent low RVR or visibility, a TAF that keeps low conditions through your arrival window, and widespread holding or diversions among comparable arrivals. None guarantees your outcome. Your airline may use a capable aircraft and crew, switch destination, carry extra fuel or delay departure until the forecast improves.
Use the airline's status for travel decisions. The airport pages provide runway and tracking context, but the official airport and aviation-weather sources govern current operations.
What happens as an aircraft approaches minimums
The crew flies the published lateral and vertical path while monitoring aircraft and ground-system status. At the applicable decision altitude or decision height, required visual references must be available for the landing to continue unless the approved operation supports a lower decision point or no decision height. If the requirements are not met, the procedure is a missed approach.
A missed approach is a planned maneuver, not evidence that the aircraft was out of control. ATC resequences the flight or the crew proceeds to the alternate plan. Fuel and forecast trends determine whether another attempt is practical. This is why a single go-around during fog can be routine while repeated approaches and diversions reveal a larger capacity problem.
Landing is only half the low-visibility problem
After touchdown, the aircraft must remain on the runway centerline, exit correctly and taxi to the gate. In dense fog, crews may have difficulty seeing signs and intersections far ahead. Airports use centerline lights, stop bars, surface radar and low-visibility taxi procedures according to their equipment and approval.
Controllers increase spacing and limit conflicting movements. Vehicles may face additional restrictions. A runway can accept an instrument landing while the taxi system remains slow, so gate arrival can lag well behind touchdown.
Audit the complete capability chain
| Link | What must be available |
|---|---|
| Airport | Approved runway, lighting, guidance and protected areas |
| Aircraft | Required sensors, autopilot redundancy and status |
| Crew | Current qualification and operator procedure |
| Weather | RVR, wind and runway condition within limits |
| Traffic | Spacing and surface movement the airport can support |
If one link fails, the operation can revert to higher minima or become unavailable. This systems view explains why two flights arriving minutes apart can make different decisions without either crew being inconsistent.
Departure also changes in dense fog
Low-visibility takeoff requires runway guidance, reported visibility or RVR, aircraft capability and operator authorization appropriate to the conditions. Crews must taxi to the correct runway and line up reliably before the takeoff roll begins. Airports can protect routes and intersections differently when visual monitoring is limited.
A departure queue may therefore move slowly even if arriving aircraft continue to land. Aircraft need greater spacing on taxiways, runway crossings take longer, and a vehicle or disabled aircraft is harder to manage. The surface can become the limiting system rather than the approach.
Fog can also be uneven. One runway's RVR sensors may report acceptable values while another's do not, or the arrival end may differ from rollout. This is why a single weather-app visibility value cannot answer whether a specific departure or landing is authorized.
When comparing airports, infrastructure matters more than size alone. A major airport can have a temporarily unavailable low-visibility runway, while a smaller equipped field may continue within its approval. Check current notices and runway status rather than assuming reputation equals capability.
Fog can improve or deteriorate quickly
Radiation fog often forms under clear skies and light wind as the surface cools, while advection fog occurs when moist air moves over a cooler surface. Low stratus can create similar operational ceilings without surface fog. Wind, temperature and dew point trends help explain the setup, but local terrain and water can make one airport behave differently from another nearby.
A narrow temperature-dew point spread in a METAR is a clue, not a forecast rule. Increasing wind can mix the lowest layer and improve visibility, or bring a new moist air mass and worsen it. Use the TAF and observations over time instead of predicting fog from one pair of numbers.
The alternate is part of the operation
When destination weather is near minimums, planning can require a suitable alternate and enough fuel to reach it under the applicable rules. The selected alternate needs weather, runway and approach capability of its own. A diversion track therefore reflects a plan made before the destination approach, not necessarily a last-second emergency.
Passengers normally see only the destination. Crews and dispatchers manage a network of options. That difference is why a safe low-visibility operation can include holding, one approach and a diversion without any failure of aircraft automation.
Surface visibility can vary across a large airport. Runway visual range sensors report conditions along particular runway zones, while a general observation summarizes the aerodrome under its reporting rules. One runway can remain usable while another approach or departure is restricted. Public summaries rarely expose every value involved in the operational decision.
After fog lifts, spacing and taxi restrictions may ease before the queue disappears. Compare the improvement time with subsequent arrival rates to separate meteorological recovery from network recovery. Wind shifts or renewed cooling can also reverse an apparent improvement.
Questions about how the system works
Can every modern airliner autoland?
Many airliners have automatic-landing capability, but availability depends on installed equipment, maintenance status, operator authorization and crew qualification. A capable type does not make every individual flight capable.
Why are flights delayed if aircraft can land automatically?
Low-visibility procedures protect guidance signals and increase spacing on runways and taxiways. Capacity falls even when individual approaches remain possible, so demand can exceed the reduced arrival rate.